Bmw Oxygen Sensor

4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream

4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream
4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream

4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream

4Pcs Upstream+Downstream Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5. Condition:100% Brand New And High Quality. Please check the picture and the part number carefully to make sure that you bought the right part for your car. Q:Why does the oxygen sensor have false alarm, after installation?

A :The clearing of the errors can be obtained on most systems when the vehicle battery is disconnected for at least 60 seconds. The assignment of the new sensor parameters is done automatically when the errors are cleared, but in some systems a short adapting tour is required. In this case the vehicle has to be driven on the road for some 10-15 minutes, in order to have the ECU adapt itself to the new sensor. Q :How do I know the O2 sensor is good or not?

A :The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation. Q :How should I install oxygen sensor? A :The following is the installation instructions: Use the correct part number as listed in the application catalogue, Do not use sensor if i has been dropped, Remove protection cap just prior to installation. Firstly install sensor body ensuring lead wire is not twisted or bent, Do not use impact wrench or socket type wrench to install sensor, M18 sensors - install finger tight then 1/2-3/4 turn with a wrench (35-45Nm).

Then connect and route lead wire as originally installed, Do not allow lead wire to touch exhaust manifold or any other hot component, Do not apply any substances (especially oil or grease) to connector sensor, Do not use leaded fuels, silicone or metal based additives. Q :When should replace the oxygen sensor?

A :Oxygen Sensor Failure Symptoms. Symptoms of a Bad Oxygen Sensor.

Code checker identifying O2 sensor failure. You can diagnose the problem yourself if you have access to the right tools OBD2 diagnostic tool. O2 Sensor Codes include P0030, P0031, P0036, P0037, P0130, P0131, P0132, P0133, P0134, and P0135. A rotten egg odor emitting from the exhaust.

A reduction in fuel economy. Your catalytic converter fails unexpectedly. Exhaust emissions reach undesirable levels. Your engine surges, hesitates, skips and bucks. We will send item to your.

If your package delayed few days, due to any unexpected factor, please wait patiently. Your kindly understanding and great patience would be highly appreciated!

If after 30 days, or the item has been used, we have the right to decline your claim. Customer Service got fired if they don't work things out with you, so knock their door at will. From Mondy to Sa t ur day , We will respond in 24 hour s.

There shall be nothing to worry about as we have c. Onfidence to solve your issue. For a presumably defective product received, this one would be a bit tricky. Please tell us where the problem occurs, and our Customer Service and Technical Department will work it through with you. Pictures and videos can come in handy here.

We wish you understand the pressures here, and our effort will always come to your aid.


4Pcs Oxygen Sensor For BMW 128i 328i 328i xDrive 328xi X3 X5 Upstream+Downstream